Tools/Maintenance

Park's Crank Puller is for removing crankarms on Shimano's splined, oversize, pipe-billet bottom brackets. It employs a long handle and a fine thread for the leverage and torque needed to remove tight arms. Park's unique rotating tip ensures smooth operation and long life. (The CCP-44 does not fit standard square or tapered bottom brackets.)

The use of cutting oil or fluid is extremely important when performing any cutting, tapping, facing or reaming operation and Park's Cutting Fluid is a high quality, environmentally safe cutting fluid that extends tool life and makes any frame prep job easier and safer. CF-2 can effectively be used on all metals.

Park Tool's Dial Indicator Kit bolts to the DT-3 (sold separately), allowing for greater accuracy and a way to measure and quantify results. NOTE: The DT-3i requires the use of the DT-3 to hold it.

Also called a sleeping hub, the Dummy Hub slides into rear dropouts and replaces the rear wheel for chain cleaning and transport. The DH-1 works with all derailleur and 1/8" chain. The unique design allows the bike to be shifted and works with open dropout and thru-axle frames up to 12mm.

Park's Folding Chain Tool is a heavy-duty tool-steel shop-quality chain tool that also folds for carrying in your pack or pocket for use on the road and trail. It's compatible with 9-, 10- and 11-speed chains. It also includes a folding peening anvil for Campagnolo 11-speed chains.

Frame Taps will become a lifesaver at some time for virtually every mechanic. As with all Park Tool Taps, these are made of high carbon steel and are precision ground. Park Tool Frame Taps cut easily and fit conventional tap handles. For water bottle, toe clip, fender and rack bosses. The TAP-8 is 5mm x 0.8 for use with water bottle, toe clip, fender and rack bosses.

Frame Taps will become a lifesaver at some time for virtually every mechanic. As with all Park Tool Taps, these are made of high carbon steel and are precision ground. Park Tool Frame Taps cut easily and fit conventional tap handles. The TAP-9 is 6mm x 1mm for cantilever brakes and large fender bosses.

12 splines, 22.6mm diameter fits Shimano, Sachs Aris, Sun Race, DNP Epoch, and other 5–10 speed freewheels. The FR-1.3 includes an enlarged thru-hole to accommodate 14mm axles.

Park's Gear Clean Brush has a handle on one end with a curved, serrated edge perfect for cleaning between cassette cogs. The other end's tough nylon bristles are ideal for cleaning the derailleurs, chain and other drivetrain parts to keep them clean and prevent premature wear. It also works great on brakes and other components that collect dirt and grime. The GearClean easily fits in a toolbox or pack.

Once you try on Park's Heavy Duty Shop Apron, there's no going back to standard aprons. The SA-3 is made from heavy 10-ounce cotton canvas and has two rows of bar tack reinforced pockets for stashing pens, parts, tools, etc. The special crossback design removes pressure from the neck for all day comfort and a nylon quick release makes the apron easy to adjust and take off. This sweet apron is a full 35-inches in length and the bottom 7-inches of the apron can be snapped up for a custom height fit. Plus, an embroidered Park Tool logo makes the apron as good looking (even when it's dirty) as it is functional.

The I-Beam Mini Fold-Up Set includes 3, 4, 5, and 6mm Allen wrenches, a socket 8mm Allen and regular screwdriver. It's the perfect mini-tool to get you out of binds or make quick adjustments. And, it conveniently tucks into a pocket or pack.

Park's Needle Nose Pliers are professional quality, 6-inches long, and made from forged, heat-treated chromoly steel. For ease of use they have a hidden spring, cutting jaws and 5 different gripping and crimping areas. Plus, they have soft-touch, dual-density handles for an excellent grip.

Made from tough steel and reinforced with extra material at the highly stressed wrench openings, Park’s shop-quality Pedal Wrench is built to easily install and remove pedals, and to last and last. It has 15mm and 9/16-inch precision openings to fit all pedals. And it boasts a long, round, vinyl-coated handle that won’t dig into your hand and provides optimum leverage. There's even a hole in the end of the wrench for hanging it on your toolboard.

Shop quality preset torque driver that limit torque applied to fasteners, preventing over tightening and damage to lightweight components. The PTD-4/PTD-5/PTD-6 feature all metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at our factory in Minnesota. - ¼ inch hex drive - Includes 3, 4, 5mm and T25 bits stored in the handle - Limits torque applied to fasteners while rotating clockwise - All metal internal construction for long life

Fills gaps and helps retain non-threaded parts like Press-fit bottom bracket parts, sealed bearings etc. Notice: Park Tool AP-1 Adhesive Primer must be used to prep all components, fasteners and carbon fiber surfaces prior to application of Park Tool threadlockers or retaining compound. Failure to do so could result in permanently bonded parts.

Park Tool's Replacement Chain Tool Pin (2-Pack) fits Park Tool's CT-1, CT-2, CT-3, CT-3.2, CT-5, and CT-7 Chain Tools. • Made from hardened alloy tool steel • Uses 7mm or 9/32" 12 pt box end/socket • Sold singly or in pairs

Park Tool's CTP-4K includes four replacement chain tool pins and one 5/32" ball bearing. To replace the chain tool pin, unscrew the cap, and pull out the old pin. Use care not to lose the ball bearing beneath the pin. Install the new pin and replace the cap. Works with the CT-4.3, CT-4.2, CT-4, and CT-11

Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)

Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. Most applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.

Park's Shop Hammer is designed specifically for use on bicycles. It features a unique dual-sided head with both steel and plastic striking surfaces, a reinforced fiberglass shaft and a soft, comfortable molded handle. The HMR-4 proves that sometimes a hammer is the best tool for the job.

Park's professional-quality, precision-sized spoke wrenches are hardened and chrome plated for long service. Wrenches are vinyl coated in one of four colors indicating the size at a glance. You will find these wrenches in virtually every professional bike shop and every shop mechanic's personal tool stash. Make sure you have the sizes you need in your home toolbox and bike bag.

This handy shop aid is ideal for sizing spokes, ball bearings, and crank cotters. To use, just hang the head of the spoke in the oblong hole and read its length on the scale. For crank cotters and ball bearings it works just like a gauge for drill bits. • Has both metric and fractional spoke length markings • Anodized aluminum with embossed markings to allow easy reading and long life

The TL-6.2 is a composite covered, steel core tire lever that provides smooth, scratch-free operation and superior strength to help remove even the tightest tires. Newly upgraded with a tougher, more slippery material and a protruding steel tip to more easily and securely engage the tire bead. A perfect size (5"/12.7cm) to either take-along, or use as an everyday shop lever. Set of two.

The small and handy RR-12.2 Tape Measure features a tough composite housing with an integrated belt clip and both metric and SAE readings up to 350 centimeters or 12 feet. Measurement can be locked in place using the thumb lock or the handy quick-stop button. - Maximum length: 350 cm | 12 ft. - Markings: 1 mm | 1/32" (up to 6") | 1/16" (over 6")

• Updated with a new material and new design • Features a wide flat tip for easy entry and fast tire removal, ergonomic shape and a handy spoke hook when multiple levers are needed • Perfect for tight beads and tubeless tires • Sold in sets of two.

Muc-Off Waterless Wash is a highly advanced, easy to use spray which cleans and polishes in seconds without the need for water. It details your whole bike, motorcycle or car in seconds leaving behind a streak free shine. Its innovative formula is designed to encapsulate any surface dirt to prevent scratching. Use it to remove light contaminants in between major washes. - Cleans and polishes in one application - No need for water - No residual dust or streaks - Powder-free - Great for eBikes - no danger of getting electrical contacts wet

- Ultra durable, long distance chain lubricant - Excel in long distance wet or muddy conditions - It penetrates deep into the chain links core to provide long lasting lubrication and total protection - Extreme pressure additives coat every part of the link to provide silky smooth gear change and ultra efficient drivetrain

- Specially formulated 10wt mineral-oil fluid for Magura hydraulic disc and rim brakes (Blue color)

Lezyne's Classic Pedal Rod is designed for heavy-duty use. Featuring two 15mm wrench openings with optimally positioned offsets, this wrench will loosen any pedal from its crank. The handle is made of varnished wood for strength and stylish good looks and there's an included bottle opener. Hang this beauty on your wall for all future pedal changes.

Lezyne's Matrix Tire Levers are winning the fight against stubborn tires. They're made of a high-strength composite material for excellent strength and durability. And, their thin hook ends easily slip under tight beads, while the large handle gives you the leverage needed for tire removal.